Confirmation sent

We emailed you a confirmation link. Please confirm your email.

got it
Join/Log in
Navigation
AUSWEIS.IO Ausweis

Ausweis Device Installation

FAQs

Please, follow all the safety steps and measures, given below. Ausweis.io does not take any responsibility for any injury and damage to the property that happened due to incorrect installation or maintenance, which run contrary to this manual.

INSTALLATION:

Step 1: Preparation

Make sure that all the following details are available in the box:

  • Ausweis Device.

  • Card with NFC-tags and stickers with QR-codes.

  • Installation manual.

  • Warranty certificate.

  • Screws (ST3.9Х22).

First of all it is necessary to choose the place in order to install the Ausweis Devicе (the device is intended for installation inside the facility, where the entrance will be controlled by Ausweis.io service). It is desirable that the device is located near the door and within a radius of WiFi network action. To install the Ausweis Device correctly, please, use the example for a wall mounting and drill holes on the wall in the place, where this device is going to be installed.

Ausweis Device is connected to the electrical network (only by means of an electric power supply) and an actuator (e.g. an electric lock).

To connect the Ausweis Device you will need not less than 4 wires (2 – the power ones and the 2 that connect the device with the actuator: for further details see the diagram). Prepare the wires in advance, put them out of the wall if necessary.

ATTENTION!

For a safe connection of the device all the elements must be deenergized.

 

Step 2: WiFi Coverage

If you wish to use the Ausweis Device in the online mode, please, make sure that the device is in the zone of a stable WiFi-coverage (we recommend this variant for you to be able to use all the functions and advantages of the Ausweis.io service).  

Without a WiFi-connection the Ausweis Device will work in the Offline-mode (due to the installed WiFi-direct), but some functions will be unavailable.  

 

Step 3: Connection of the device

Recommended tools and equipment for the installation:

1. An electrical drill.

3. A pencil and a yard-measure.

4. A stranded cable (recommended 22/4 Gauge AWG Alarm Security Wire Cable).

5. A device for voltage measurement (e.g. a multimeter).

IMPORTANT!

  • Do not try to modify or repair the device with your own hands.  

  • Do not connect any secondary devices, not mentioned in this manual, to Ausweis Device.

  • Before drilling the holes for installation of the Ausweis Device make sure that there is no electrical wiring, cables or other communication lines in the chosen place.  

  • Before connecting the wires make sure that they are deenergized.

The work for installation of the Ausweis Device requires technical knowledge and appropriate skills.  We do not recommend fulfilling this kind of work by people who do not have a necessary qualification. Please, consult a specialist who has experience of fulfilling such installation work. To learn more about the list of recommended installations, please, follow:  www.ausweis.io

IMPORTANT!

For a correct connection of the device, please, use our connection diagrams.

On the terminal block that is on the Ausweis Device board, terminal markings are given (+V, GND, DOOR SENSOR, COM 1, NO/NC R1, COM 2, NO/NC R2). Connect the power wires and the actuator to the corresponding joints on the Ausweis Device. The power wire “+” must be connected to the plug “+V” on the device. The power wire “-” must be connected to the plug “GND”.  Connect the wires that go to the actuator to the plugs NO/NC R1 and COM 1.

 

Step 4: Checking

Check the correctness of the connection visually (connection of the wires to the corresponding plugs), then give pressure (turn on the power supply). If the device was installed correctly, the indicator on the front panel (upper cover) will light up white. After that the Ausweis Device is ready for registration in the mobile application Ausweis (the available versions are for iOS and Android).

REGISTRATION OF THE AUSWEIS DEVICE IN THE APPLICATION.:

Step 1: Create a profile in the application.

If you have not installed the mobile application Ausweis, download it from AppStore or Google Play. While creating a profile in the application, use an actual email address and your telephone number, which can be easily accessed. Lear more

 

Step 2: Add a lock

After finishing the registration process of the profile you can add your new lock. To do so go to the tab MY LOCKS and click on the button “+”, located on the right upper corner of the screen. Then follow the step by step manual:

Android User: choose your device Ausweis from the list, a lock type and a work mode, enter the name, address and choose the mode (Online or Offline). 

iOS User: scan a QR-code, located on the plate of the Ausweis Device.

Please, make sure that during your registration of the lock you have access to the stable Internet connection.  

After registering of the Ausweis Device 10 free-of-charge digital keys will be available for you, which you can share with your relatives and confidants.   
 

Step 3: Test the Ausweis Device

Check your device by touching a green indicator on it or by opening the lock in the Ausweis mobile app. The lock must open immediately.

Diagram for connection to the electromechanical lock:
Diagram for connection to the electromagnetic lock:
Connection to the Access Control System (type 1):
Connection to the Access Control System (type 2):

Ausweis Device Installation

FAQs

Please, follow all the safety steps and measures, given below. Ausweis.io does not take any responsibility for any injury and damage to the property that happened due to incorrect installation or maintenance, which run contrary to this manual.

INSTALLATION:

Step 1: Preparation

Make sure that all the following details are available in the box:

  • Ausweis Device.

  • Card with NFC-tags and stickers with QR-codes.

  • Installation manual.

  • Warranty certificate.

  • Screws (ST3.9Х22).

First of all it is necessary to choose the place in order to install the Ausweis Devicе (the device is intended for installation inside the facility, where the entrance will be controlled by Ausweis.io service). It is desirable that the device is located near the door and within a radius of WiFi network action. To install the Ausweis Device correctly, please, use the example for a wall mounting and drill holes on the wall in the place, where this device is going to be installed.

Ausweis Device is connected to the electrical network (only by means of an electric power supply) and an actuator (e.g. an electric lock).

To connect the Ausweis Device you will need not less than 4 wires (2 – the power ones and the 2 that connect the device with the actuator: for further details see the diagram). Prepare the wires in advance, put them out of the wall if necessary.

ATTENTION!

For a safe connection of the device all the elements must be deenergized.

 

Step 2: WiFi Coverage

If you wish to use the Ausweis Device in the online mode, please, make sure that the device is in the zone of a stable WiFi-coverage (we recommend this variant for you to be able to use all the functions and advantages of the Ausweis.io service).  

Without a WiFi-connection the Ausweis Device will work in the Offline-mode (due to the installed WiFi-direct), but some functions will be unavailable.  

 

Step 3: Connection of the device

Recommended tools and equipment for the installation:

1. An electrical drill.

3. A pencil and a yard-measure.

4. A stranded cable (recommended 22/4 Gauge AWG Alarm Security Wire Cable).

5. A device for voltage measurement (e.g. a multimeter).

IMPORTANT!

  • Do not try to modify or repair the device with your own hands.  

  • Do not connect any secondary devices, not mentioned in this manual, to Ausweis Device.

  • Before drilling the holes for installation of the Ausweis Device make sure that there is no electrical wiring, cables or other communication lines in the chosen place.  

  • Before connecting the wires make sure that they are deenergized.

The work for installation of the Ausweis Device requires technical knowledge and appropriate skills.  We do not recommend fulfilling this kind of work by people who do not have a necessary qualification. Please, consult a specialist who has experience of fulfilling such installation work. To learn more about the list of recommended installations, please, follow:  www.ausweis.io

IMPORTANT!

For a correct connection of the device, please, use our connection diagrams.

On the terminal block that is on the Ausweis Device board, terminal markings are given (+V, GND, DOOR SENSOR, COM 1, NO/NC R1, COM 2, NO/NC R2). Connect the power wires and the actuator to the corresponding joints on the Ausweis Device. The power wire “+” must be connected to the plug “+V” on the device. The power wire “-” must be connected to the plug “GND”.  Connect the wires that go to the actuator to the plugs NO/NC R1 and COM 1.

 

Step 4: Checking

Check the correctness of the connection visually (connection of the wires to the corresponding plugs), then give pressure (turn on the power supply). If the device was installed correctly, the indicator on the front panel (upper cover) will light up white. After that the Ausweis Device is ready for registration in the mobile application Ausweis (the available versions are for iOS and Android).

REGISTRATION OF THE AUSWEIS DEVICE IN THE APPLICATION.:

Step 1: Create a profile in the application.

If you have not installed the mobile application Ausweis, download it from AppStore or Google Play. While creating a profile in the application, use an actual email address and your telephone number, which can be easily accessed. Lear more

 

Step 2: Add a lock

After finishing the registration process of the profile you can add your new lock. To do so go to the tab MY LOCKS and click on the button “+”, located on the right upper corner of the screen. Then follow the step by step manual:

Android User: choose your device Ausweis from the list, a lock type and a work mode, enter the name, address and choose the mode (Online or Offline). 

iOS User: scan a QR-code, located on the plate of the Ausweis Device.

Please, make sure that during your registration of the lock you have access to the stable Internet connection.  

After registering of the Ausweis Device 10 free-of-charge digital keys will be available for you, which you can share with your relatives and confidants.   
 

Step 3: Test the Ausweis Device

Check your device by touching a green indicator on it or by opening the lock in the Ausweis mobile app. The lock must open immediately.

Diagram for connection to the electromechanical lock:
Diagram for connection to the electromagnetic lock:
Connection to the Access Control System (type 1):
Connection to the Access Control System (type 2):